Tag Kernel crc : 0圆0CE85C1 - calculated: 0圆0CE85C1 Trying to boot from FIRST image copy (0x80010000). *** Press any key to stop auto run (1 seconds) *** Note that while the tag on the image say this is an AGPF-S0 board, the web interface tell you this is an AGPF-S1. Relocation Factor: I:00000000 - D:00000000ĭefault host flash file name : openrg.img Sudo dnsmasq -d -enable-tftp -tftp-root=`pwd`ĬFE> flashimage openwrt-AGV2+W-cfe-jffs2-128k-cfe.bin That's all, the device will automaticly reboot and openwrt will be there To get the CFE prompt you must turn on you router and when you see a countdown and you must press 'enter'.Įg. If you configure (with command c) the host ip address you can avoid it in the flashimage argument. Now you have to use the flashimage command to load the openwrt image, please don't use the f command. Put the choose image in the right place (see your tftp server configuration), and go to the CFE prompt. #FIRMWARE MODEM ALICE GATE VOIP 2 PLUS WIFI CARD DOWNLOAD#Now just download the image for AGV2+W from, skip the jffs2 with 64k erase block as the flash use 128k block, anyway using 64k should not give much problem, just some wasted space and some errors messages. #FIRMWARE MODEM ALICE GATE VOIP 2 PLUS WIFI CARD WINDOWS#If you use Windows you can use tftpd32 to configure the tftpd server and the directory shared (you must connect also by lan your router and your pc). You need to setup a tftp server on some host (I can suggest to use dnsmasq for this) to serve the firmware image to the router. Going to reboot! Restore original firmware Now unmount your flash key, put the file in a safe place and reboot the Alice stopping the boot process at the bootloader prompt pressing some keys. #FIRMWARE MODEM ALICE GATE VOIP 2 PLUS WIFI CARD FULL#If you prefer you can use an ext2 or ext3 formatted filesystem.įrom this file you can extract all you need to do a full restore of your device, both via jtag or via CFE. This will create a 16M file named MTDBLOCK (due to fat limitation). mnt # dd if=/dev/mtdblock0 of=/mnt/backup/mtdblock dev/mtd1 /dev/mtd_rgconf1 /dev/mtdblock3 /dev/mtdr3 dev/mtd0 /dev/mtd_rgconf0 /dev/mtdblock2 /dev/mtdr2 Now just copy the content of the flash in some files on the usb key. VFS: Can't find an ext2 filesystem on dev sda1. VFS: Can't find ext3 filesystem on dev sda1. Insert an USB flash key into the usb port of the router and mount the new device somewhere, for example in /mnt/backup Note: the first time you will not see Username, but if you write admin, router will request you the password.īusyBox v1.01 (2005.09.07-07:38+0000) Built-in shell (lash)Įnter 'help' for a list of built-in commands. To obtain the shell just digit system shell. #FIRMWARE MODEM ALICE GATE VOIP 2 PLUS WIFI CARD PASSWORD#You have only to wait and don't have to short-circuit RX and TX pin.Īt the login prompt use admin as username and password to get to the openrg Discus prompt.įrom the Discus prompt you can do a lot of useful things, but i've not explored it due to some lack of interest. #FIRMWARE MODEM ALICE GATE VOIP 2 PLUS WIFI CARD SERIAL#Note, when you flash from jtag the BASE ADDRESS is 0x1E000000Ĭonnect the serial adapter and let the device complete the boot procedure. I don't understand the MaxSize value of some sections as they leave some space before the next section. More detailed information came from the discuss prompt:
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |